How do I check my promotion points army?
Steps to access your PPW – Soldiers (Private (E1) – Sergeant(5)) can log into the PPW from the AKO website. – Under Army Links click on Enlisted Promotions, at the bottom of the screen, check the box left of submit, then click the submit button.
What Orb means?
Object Request Broker
What does Orb stand for in text?
Technology, IT etc (11) ORB — Off-world Resource Base. ORB — Online Resource Bank. ORB — Oak Ridge Boys.
What does Orb mean in law?
0AB is the Judge’s designation. The court clerk should be able to tell you the Judge’s name. 8-5 means that the case will be heard at the Kelso Drive courthouse in Essex… 1 found this answer helpful found this helpful | 0 lawyers agree.
What does Orb fitting stand for?
O-Ring Boss
Are SAE and ORB the same?
O-Ring Boss: The threads of the SAE straight thread O-Ring Boss (ORB) and the straight thread 37⁰ JIC Flare are the same threads. The difference is the way each thread seals. While the JIC seals on a metal-to-metal flare, the ORB seals on an O-ring, which offers the best leak free connection.
Do an fittings need an O-ring?
Port fittings require O-rings. Like AN Adapters, special port machining is done to capture and properly compress the O-ring, which allows for greater sealing ability with very high reliability of installation compared with tapered threads using sealing compounds or Teflon tape.
What is an O-ring port?
AN O-Ring Port Adapters are used with oil pump, fuel rails, filters, filter adapters, and other parts that are machined with AN Female straight threads. The O-ring on these adapters is used to seal the fitting to other component.
What is a SAE #20 O-ring port?
SAE O-ring (O-Ring Boss) are straight thread fittings that seal using a O-ring between the thread and the wrench flats of the fitting. The O-ring seals against the machined seat on the female port. This makes it easier to strip threads or crack or distort fitting components, which prevents proper sealing.
What is an O-ring boss fitting?
An o-ring boss seal is a technique for joining two fluid-carrying pipes, hoses, or tubing. In an o-ring boss (abbreviated ORB) system, a male-threaded part is inserted into a female-threaded part, providing a mechanical seal. This system has the advantage of being able to be tightened mechanically before being sealed.
What size is SAE 12?
SAE 45° Flare (SAE J512)
| Inch size | Dash size | Male Thread O.D. (in) |
|---|---|---|
| 5⁄8 | -10 | 7⁄8 |
| 3⁄4 | -12 | 11⁄16 |
| 7⁄8 | -14 | 1 1⁄4 |
| 1 | -16 | 1 3⁄8 |
What size is SAE 8 in inches?
The number commonly used for hydraulic hoses, tubes and fittings is the number of 16th of an inch. So an 8 is 8/16 or 1/2″.
How do I know my JIC size?
Subject: RE: How can you tell what size of JIC hyd fittings you have? The tube fitting size number is the number of 1/16″ of the tube or fitting. That is a number 4 is 4*1/16 or 4/16 which is 1/4″ and so forth, a number 8 is 1/2″ a 16 is one inch.
How do I know what size hydraulics to get?
How to Measure Your Hydraulic Fitting
- First you should determine the length of a hydraulic fitting by laying it on a table and then stretching your measuring tape across the top of it.
- Next, determine the outside diameter of the fitting by using your ID/OD calipers.
Do you need Teflon tape on hydraulic fittings?
You don’t need or should use any teflon tape or pipe dope on hydraulic fittings. Neither are designed for those kinds of pressures and using them could create a less then perfect mating between connection surfaces causing more harm than good.
What are hydraulic fittings called?
The three most common types of hose fittings are O-ring, mated angle and threaded. However, there are several more types of hydraulic hose fittings available. O-Ring: The three types of O-ring seal designs are O-ring boss, flat face O-ring seal and O-ring flange.
How are hydraulic couplers measured?
Measuring and identifying the fittings is easily done but you must have the correct tools. Use a caliper to measure thread inner and outer diameters. To measure the thread’s outer diameter (or male thread), place the ID/OD caliper around the fitting threads for a snug fit, as shown in Figure 2.
How do I know what type of thread?
- Determine if the thread is straight (parallel) or tapered. The thread is tapered if the diameter increases or decreases.
- Measure the thread diameter.
- Determine the number of threads per inch (TPI) or the pitch (metric threads) with the thread gauge.
- Determine the thread standard.
How do you determine your fitting size?
You can always identify AN fittings based on the male thread size (outside diameter). These sizes are constant regardless of brand, hose type, or fitting configuration. If your fitting has a convex 37 degree flare at the end, the threads will tell you the AN size (and vice-versa).
How is quick disconnect size measured?
Lay the hose over a ruler or tape measure. If the hose is 5/8” wide it is a 3/8” ID hose. If the hose measures ¾” wide, it is a 1/2” ID hose. (2) Measure the internal diameter of the quick disconnect.
How do you measure a coupler?
Coupler Size. — Understand that coupling size is an industry designation, not the actual measured size. For parts with a female (sockets) coupler end the size is determined by measuring the open end (x) of the coupler. — For the male (plug) adapter the coupling size is determined by measuring the adapter/plug end (y).